LP01-V (1000 W) 
LP03-V (3000 W)

LP05-V (5000 W)
LP10-V (10.000 W)

LP05-H (5 kW)  
LP10-H (10 kW) 
LP20-H (20 kW)

LP30-H (30 kW)
LP50-H (50 kW)
LP100-H (100k W)

Controller

Touch Screen PLC, Remote monitoring: Optional

safety

Pitch Control, Active Yaw Control

Tower

Monopole Tower:12m, 18m, 24m, 30m

Mechanical Pitch Control:

LisePro intelligent pitch control, can change the blade angle to output more power at low wind speed and stable power output at high wind speed. It will protect the wind turbine from excessive wind.

Speed, over speed and other faults. All pitch control parts in LisePro are mechanical parts without hub, electronic parts. This is more reliable than traditional electronic pitch control system.

Active Yaw Control:

Active yaw control system will provide automatic tracking of wind turbine. Automatic deviation from wind direction when wind direction and automatic deviation

It is necessary to protect wind turbine over wind speed or other faults. It may protect wind turbine even if pitch control system fails.

Two Shaft Hydraulic Brakes:

There are two shaft hydraulic brakes for LisePro-H 50kw wind turbine. They are driven by high quality hydraulic station. They can stop wind turbine in any emergency even without pitch control, protection and yaw control protection.

80kW Unloading Load Box:

LisePro-H 50kw has PWM unloading loading protection. overvoltage fault. A 80kw dump load box will control the peak voltage together with the pitch control system. It will make the power output more stable at high wind speed.

Grid Failure and Power Loss Protection:

When there is a grid failure or other reasons that cause electricity loss, such as cable breakage, PLC damage, etc. Our wind turbine can still stop automatic pitch control and start hydraulic brake system. It is physical self-protection in the nacelle.

Double Safety Design:

LisePro uses double safety design for the main functions of the wind turbine. One pitch control motor, one yaw motor and gearbox, two shaft hydraulic brake and two different UPS system in the motor compartment. If the hydraulic brake or UPS is damaged, the other one can still work well to control the wind turbine.

Low RPM and Direct Drive Generator:

LisePro 50kW is a direct drive permanent magnet generator without gear. It is more reliable and requires less maintenance. induction generator. We use low rpm and larger generator diameter design. This means higher costs, but better performance in power generation, reliability and overheating problem.

Direct Connection Design:

The hub is directly connected to the generator shaft. The generator is directly connected to the nacelle. The generator shaft is directly connected to the brake disc. The optimized design for LisePro has eliminated the traditional adapter flanges and welding parts. This makes the wind turbine more reliable and more safety.

Larger Rotor and More Power Output:

LisePro-H 50 kW has a rotor diameter of 17.6 m, which is the same. Even larger than some 50 kW wind turbines. It will reach 20kW output at 8m/s wind speed and has more power output in low wind speed area. Annual power output is about 180.83 MWh at 6 m/s wind speed.

IEC 61400-2 Casting Parts:

LisePro-H 50kW hub and nacelle are all casting parts, followed by IEC 61400-2 standard. Nacelle and hub are made by EN-GJS-400-LT MW wind turbines, which have the same material and technology as EN-GJS-400-LT. Lifetime design is more than 27 years, and can work in -20℃ to 50℃. More reliable than welding hub and nacelle.

Low Maintenance Cost:

There is automatic grease lubricator in nacelle. Automatically lubricate yaw bearing, pitch control bearing and other bearings. People could access the nacelle from inside the tower.

LisePro uses Programmable Logic Controller (PLC) and Touch Screen as control system. The whole operation data such as wind speed and power output can be recorded, and customer can easily set the protection data such as wind speed, voltage, current and rpm through the controller.

LisePro provides remote monitoring function to its customers. You can monitor and control the wind turbine remotely. Operation at home, office, airport and anywhere via wireless or wired internet

The LisPro-H-50kW wind turbine will operate with a POWER Converter 60kW grid on inverter with CEI 0-21 certification for connection to the public grid.

LisePro-H 50kW wind turbine is paired with Win-50kW-G Wind Three Phase Inverter. LisePro engineers in Germany have done a lot of work in-house and on-site to make the system work more efficiently and we have developed a more reliable system.